1995-2004 Tacoma Rear Leaf Springs

% of 100
As low as $783.20 Regular Price $979.00
100+ In Stock
Only %1 left
95-04 Tacoma Rear Leaf Springs

Our ’95-’04 Tacoma rear leaf springs are a direct fit for the ’98-’04 Tacoma. They will also fit the ’95-’97 Tacoma with modifications to the spring hangers (see note below). These springs have a special torque leaf to reduce axle wrap. Springs come with new poly bushings and sleeves.

NOTE! Mounting our springs on 95-97 Tacomas will require relocating new front spring hangers 2″ forward and the rear shackle hangers 1" rearward from their stock configurations.

All-Pro’s Standard Duty leaf springs (4500T-AP) are NOT designed for heavy weight carrying capability. They are designed for ride quality and flex. For those carrying heavier loads such as rigs fully loaded for long-term expeditions, we recommend All-Pro “Expedition” Heavy Duty rear springs.

All-Pro’s new Expedition leafs are specifically designed to combine off-road performance with heavy duty weight carrying capacity. The popular expedition style trend in off-road vehicles is resulting in trucks that are carrying heavier loads than normally seen off-road. Specialized long-distance excursion gear such as roof-top tents, recovery and repair gear, camping equipment and extra water and fluids can add significantly to the cargo weight of expedition vehicles, exceeding the intended operating parameters of typical performance leaf springs.

All-Pro’s Expedition Leaf Springs (4500T-AP-EX) feature a 20% higher spring rate than our standard leaf springs. They are otherwise identical in dimension and quality, providing the same eye-to-eye measurements and wheel travel.

APPROXIMATE LIFT - The Standard Springs will provide approximately 3" of lift. The Expedition Springs will provide approximately 3" of lift with 400-500 lbs of cargo. Unloaded, they will provide approximately 4" of lift.


* A higher number of thinner leaves provides a smoother, progressive spring rate compared to fewer, thicker leaves
* Double “military” wrap provides extra strength for the main leaf
* “Torque Leaf”, an extra half-leaf at the top of the spring pack, increases anti-wrap properties without hindering travel or ride quality
* Diamond-cut leaf ends to eliminate stress points which may weaken leafs and lead to premature failure
* Teflon anti-friction pads between leafs provide smoother flex, lessen spring wear and reduce noise
* Leafs are shot-peened after forming to relieve stress
* Every completed spring pack is pre-cycled to their travel extremity for quality control and to reduce the likelihood of initial sag

Please Note:

After installation, the stock rear bumps will no longer be sufficient to prevent the spring from inverting. You must purchase and install a set of bump stops that are of sufficient height to prevent the spring from going negative arch. For best results, we recommend Wheeler’s SuperBumps (sold separately).

Failure to use bump stops of sufficient height may void the spring warranty.

  • Use of lifting blocks or shackle flip kits will void all warranty on All-Pro Leaf Springs!
  • Leaf springs are shipped without packaging. It is normal for springs to be scratched by freight carriers during the shipping and handling process and by customers during installation. We recommend that leaf springs be touched up with spray paint after they are installed to cover any bare metal exposed during shipping and installation.
Leaf springs are received from the manufacturer without packaging and are shipped to you without packaging. The paint finish may be scratched by the freight carriers during the shipping process. The leaf springs can be spray painted to cover any bare metal exposed during the shipping/handling process. It's best to wait until after they are installed before you touch them up as they may also be scratched during the installation process.

⚠ WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Standard Duty Leaf Spring Specifications:

  • Number of Leaves:  7 + 1 Overload/Rebound
  • Eyelet-to-Eyelet Length (Free):  51-5/8″ (1311 mm)
  • Spring Rate:  154 lbs/in

Expedition Leaf Spring Specifications:

  • Number of Leaves:  6 + 1 Overload/Rebound
  • Eyelet-to-Eyelet Length (Free):  51-1/4″ (1302 mm)
  • Spring Rate:  207 lbs/in


1995 Toyota Tacoma (Mods Req'd - See Desc)
1996 Toyota Tacoma (Mods Req'd - See Desc)
1997 Toyota Tacoma (Mods Req'd - See Desc)
1998 Toyota Tacoma
1999 Toyota Tacoma
2000 Toyota Tacoma
2001 Toyota Tacoma
2002 Toyota Tacoma
2003 Toyota Tacoma
2004 Toyota Tacoma

1. Install bushings into the springs using polyurethane-safe grease. If applicable, install the sleeves into the bushings.

2. Mount the springs to the vehicle. The end with the military wrap should be at the front.

3. Check to make sure the long side of the bolts on the spring clamps are pointed towards the inside of the vehicle.

4. Fully cycle the suspension and verify that no part of the springs interfere with other suspension components (e.g. shocks). Also verify that the brake lines are long enough and do not stretch at maximum droop or get pinched by other components. In some instances, leaf spring clamps may need to be removed or relocated to avoid interference with other components.

5. If you have any questions or concerns, please e-mail your questions to tech@trail-gear.com
or call us at 559.549.6737.

All-Pro Warranty_image

ALL-PRO products are warranted to be free from defects in materials and workmanship prior to installation. Any alteration, improper use, or modification will void this warranty. This warranty is extended by All-Pro to the original purchaser.  This warranty is effective for 90 days from the date of purchase. Any description of the goods is for the sole purpose of identifying them, is not a part of the bargain, and does not constitute a warranty that the goods will conform to that description.  Any sample, model or advertised item is for illustrative purposes only, is not part of the basis for the bargain, and is not to be construed as a warranty that the good will conform to the sample, model, or advertised item. No affirmation of fact or promise made by All-Pro will constitute a warranty that the goods will conform to the affirmation or promise.

Purchasers and users of our products are responsible for determining the applicability of a product to their specific application. In the event of a defect, malfunction, or failure to conform to this warranty, All-Pro will repair or replace the goods without charge within 30 days of receipt of goods.  If All-Pro is unable to replace and/or repair the goods or if All-Pro, at its sole discretion, determines that neither option is commercially practicable or cannot be made within 30 days of receipt of the goods, All-Pro will refund the purchase price. The purchaser is responsible for installation and removal of all parts, freight or shipping costs, and incidental or consequential damages.


Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
Copyright © 2023 ALL-PRO OFF-ROAD. All rights reserved.